2016.07.13 – Cisco Official News:
400-101 CCIE Routing and Switching Written Exam 1119Q&As New Updated Today!
Instant Free Download 400-101 PDF & 400-101 VCE from Braindump2go.com!
100% Exam Pass Guaranteed!
NEW QUESTION 1070 – NEW QUESTION 1080:
1.|Braindump2go 2016.07 Cisco 400-101 CCIE Exam PDF and VCE 1119Q&As Dumps Download:
http://www.braindump2go.com/400-101.html
[100% Exam Pass Guaranteed!]
2.|Braindump2go 2016.07.13 Cisco 400-101 CCIE Exam Questions PDF Download:
https://drive.google.com/folderview?id=0B272WrTALRHcQ1VmTHBkOEFvV00&usp=sharing
QUESTION 1
Which two options are reasons for TCP starvation? (Choose two.)
A. The use of tail drop
B. The use of WRED
C. Mixing TCP and UDP traffic in the same traffic class
D. The use of TCP congestion control
Answer: CD
QUESTION 2
Which type of port would have root guard enabled on it?
A. A root port
B. An alternate port
C. A blocked port
D. A designated port
Answer: D
QUESTION 3
Refer to the exhibit. Which action will solve the error state of this interface when connecting a host behind a Cisco IP phone?
A. Configure dot1x-port control auto on this interface
B. Enable errdisable recovery for security violation errors
C. Enable port security on this interface
D. Configure multidomain authentication on this interface
Answer: D
QUESTION 4
Refer to the exhibit. While troubleshooting high CPU utilization of a Cisco Catalyst 4500 Series Switch, you notice the error message that is shown in the exhibit in the log file.
What can be the cause of this issue, and how can it be prevented?
A. The hardware routing table is full. Redistribute from BGP into IGP.
B. The software routing table is full. Redistribute from BGP into IGP.
C. The hardware routing table is full. Reduce the number of routes in the routing table.
D. The software routing table is full. Reduce the number of routes in the routing table.
Answer: C
QUESTION 5
Refer to the exhibit. All switches have default bridge priorities, and originate BPDUs with MAC addresses as indicated. The numbers shown are STP link metrics. Which two ports are forwarding traffic after STP converges? (Choose two.)
A. The port connecting switch SWD with switch SWE
B. The port connecting switch SWG with switch SWF
C. The port connecting switch SWC with switch SWE
D. The port connecting switch SWB with switch SWC
Answer: CD
QUESTION 6
Refer to the exhibit. While troubleshooting high CPU utilization on one of your Cisco Catalyst switches, you find that the issue is due to excessive flooding that is caused by STP. What can you do to prevent this issue from happening again?
A. Disable STP completely on the switch.
B. Change the STP version to RSTP.
C. Configure PortFast on port-channel 1.
D. Configure UplinkFast on the switch.
E. Configure PortFast on interface Gi0/15.
Answer: E
QUESTION 7
Refer to the exhibit. Which three statements about the output are true? (Choose three.)
A. An mrouter port can be learned by receiving a PIM hello packet from a multicast router.
B. This switch is configured as a multicast router.
C. Gi2/0/1 is a trunk link that connects to a multicast router.
D. An mrouter port is learned when a multicast data stream is received on that port from a multicast router.
E. This switch is not configured as a multicast router. It is configured only for IGMP snooping.
F. IGMP reports are received only on Gi2/0/1 and are never transmitted out Gi2/0/1 for VLANs 10 and 20.
Answer: ABC
QUESTION 8
Refer to the exhibit. If a port is configured as shown and receives an untagged frame, of which VLAN will the untagged frame be a member?
A. VLAN 1
B. VLAN 2
C. VLAN 3
D. VLAN 4
Answer: B
QUESTION 9
Refer to the exhibit. Which statement describes the effect on the network if FastEthernet0/1 goes down temporarily?
A. FastEthernet0/2 forwards traffic only until FastEthernet0/1 comes back up.
B. FastEthernet0/2 stops forwarding traffic until FastEthernet0/1 comes back up.
C. FastEthernet0/2 forwards traffic indefinitely.
D. FastEthernet0/1 goes into standby.
Answer: C
QUESTION 10
Refer to the exhibit. Routers R1, R2, and R3 are configured as shown, and traffic from R2 fails to reach 172.29.168.3.
Which action can you take to correct the problem?
A. Correct the static route on R1.
B. Correct the default route on R2.
C. Edit the EIGRP configuration of R3 to enable auto-summary.
D. Correct the network statement for 172.29.168.3 on R3.
Answer: A
!!!RECOMMEND!!!
2016.07 Braindump2go Latest Cisco 400-101 Exam PDF and VCE 1119Q&As Instant Download:
http://www.braindump2go.com/400-101.html [100% Real Questions Guaranteed!]
Cisco 400-101 Exam Questions PDF – Google Drive:
https://drive.google.com/folderview?id=0BwwEErkugSaLbUR5WjhsemNKY00&usp=sharing
https://drive.google.com/folderview?id=0B75b5xYLjSSNdmdKVDE2WUw4VGM&usp=sharing