Free 2014 Cisco 200-101 Dump (61-70) Download!

QUESTION 61
Hotspot Question

R1 is configured with the default configuration of OSPF. From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID?

A.    192.168.0.1
B.    172.16.1.1
C.    172.16.2.1
D.    172.16.2.225

Answer: A
Explanation:
The Router ID (RID) is an IP address used to identify the router and is chosen using the following sequence:
+ The highest IP address assigned to a loopback (logical) interface. + If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen.
+ The router ID can be manually assigned
In this case, because a loopback interface is not configured so the highest active IP address 192.168.0.1 is chosen as the router ID.

QUESTION 62
Hotspot Question

If required, what password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router?

A.    No password is required.
B.    Enable
C.    Secret
D.    Telnet
E.    Console

Answer: B
Explanation:
In the diagram, DeepSouth is connected to Dubai’s S1/2 interface and is configured as follows:
Interface Serial1/2
IP address 192.168.0.5 255.255.255.252
Encapsulalation PPP ; Encapsulation for this interface is PPP
Check out the following Cisco Link:
http://www.cisco.com/en/US/tech/tk713/tk507/technologies_configuration_example09186a00800 94333.shtml#configuringausernamedifferentfromtheroutersname
Here is a snipit of an example:
Network Diagram
If Router 1 initiates a call to Router 2, Router 2 would challenge Router 1, but Router 1 would not challenge Router 2. This occurs because the ppp authentication chap callin command is configured on Router 1. This is an example of a unidirectional authentication. In this setup, the ppp chap hostname alias-r1 command is configured on Router 1. Router 1 uses “alias-r1” as its hostname for CHAP authentication instead of “r1.” The Router 2 dialer map name should match Router 1’s ppp chap hostname; otherwise, two B channels are established, one for each direction.

QUESTION 63
Hotspot Question

What would be the destination Layer 2 address in the frame header for a frame that is being forwarded by Dubai to the host address of 172.30.4.4?

A.    825
B.    230
C.    694
D.    387

Answer: C
Explanation:
According to command output 172.30.4.4 is using the 694 dlci value. http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp1029343

QUESTION 64
Hotspot Question

Which connection uses the default encapsulation for serial interfaces on Cisco routers?

A.    The serial connection to the NorthCoast branch office.
B.    The serial connection to the North branch office.
C.    The serial connection to the Southlands branch office.
D.    The serial connection to the Multinational Core.

Answer: B
Explanation:
Cisco default encapsulation is HDLC which is by default enabled on all cisco router. If we want to enable other encapsulation protocol(PPP,X.25 etc) we need to define in interface setting. But here except s1/1 all interface defined by other encapsulation protocol so we will assume default encapsulation running on s1/1 interface and s1/1 interface connected with North

QUESTION 65
Hotspot Question

A static map to the S-AMER location is required. Which command should be used to create this map?

A.    frame-relay map ip 172.30.0.3 825 broadcast
B.    frame-relay map ip 172.30.0.3 230 broadcast
C.    frame-relay map ip 172.30.0.3 694 broadcast
D.    frame-relay map ip 172.30.0.3 387 broadcast

Answer: B
Explanation:
frame-relay map ip 172.30.0.3 230 broadcast 172.30.0.3 is S-AMER router ip address and its configure on 230 dlci value. Check “show frame-relay map ” output in the diagram.

QUESTION 66
Which command displays the CHAP authentication process as it occurs between two routers?

A.    debug chap authentication
B.    debug authentication
C.    debug chap ppp
D.    debug ppp authentication

Answer: D

QUESTION 67
A department decides to replace its hub with a Catalyst 2950 switch that is no longer needed by another department. To prepare the switch for installation, the network administrator has erased the startup configuration and reloaded the switch. However, PCs that are connected to the switch experience various connectivity problems. What is a possible cause of the problem?

A.    The VLAN database was not erased.
B.    The management VLAN is disabled.
C.    The running configuration should have been erased.
D.    The “mode” button was not pressed when the switch was reloaded.
E.    The switch was not configured with an IP address or a default gateway.

Answer: A

QUESTION 68
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)

A.    Global addresses start with 2000::/3.
B.    Link-local addresses start with FE00:/12.
C.    Link-local addresses start with FF00::/10.
D.    There is only one loopback address and it is ::1.
E.    If a global address is assigned to an interface, then that is the only allowable address for the interface.

Answer: AD

QUESTION 69
What are three features of the IPv6 protocol? (Choose three.)

A.    optional IPsec
B.    autoconfiguration
C.    no broadcasts
D.    complicated header
E.    plug-and-play
F.    checksums

Answer: BCE

QUESTION 70
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

A.    Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B.    Add a second router to handle the VLAN traffic.
C.    Add two more Fast Ethernet interfaces.
D.    Implement a router-on-a-stick configuration.

Answer: D

If you want to pass the Cisco 200-101 Exam sucessfully, recommend to read latest Cisco 200-101 Dumpfull version.